If % error in length diameter current and voltage are same than which of the following affects %error in measurenet of resistivity the most .

Monjur Alahi

If % error in length diameter current and voltage are same than which of the following affects %error in measurenet of resistivity the most .
A. length measurement
B. voltagemeasurement
C. current measurement
D. diameter measurement


0 like 0 dislike
2 views
Share with your friends

1 Answers

Salim Ahmed Kawsar

Call

`((Dletarho)/(rho))_(max)` = is mostly affected by % error in diameter .

0 like 0 dislike
2 views
Talk Doctor Online in Bissoy App
The electrical resistance of a column of 0.04M NaOH solution of diameter 1.2 cm and length 50cm is `5.55xx10^(3)ohm`, the resistivity of the column wo

Correct Answer - A `r=(1.2)/(2)= 0.6cm` `alpha=pir^(2)=3.14xx(0.6)^(2)` `=3.14xx0.36=1.13cm^(2)` `l=50cm` `R=rho(l)/(alpha)` `rho=(R,alpha)/(l)=(3.55xx10^(3)ohmxx1.13cm^(2))/(50cm)` `=1.2547xx10^(2)` ohm cm `=125.47` ohm cm

2 Answers 4 views
Statement-1 : The induced e.m.f. and current will be same in two identical loops of copper and aluminium, when rotated with same speed in the same mag

Correct Answer - D Since, both the loops are identical (same area and number of turns) and moving with a same speed in same magnetic field. Therefore, same emf is induced...

2 Answers 1 views
The resistivity of iron is `1 xx 10^(-7) ohm-m` . The resistance of a iron wire of particular length and thickness is 1 ohm . If the length and the di

Correct Answer - A Resistivity does not depend on length & cross section area.

2 Answers 2 views
a) The peak voltage of an AC supply is 300 V. What is the rms voltage? b) The rms value of current in an AC circuit is 10A. What is the peak current?

a) Heak, peak value of AC supply, `V_(0) = 300V` `therefore` Using the relation `V_(rms) = V_(0)/sqrt(2)` We get, `V_(rms) = 300/sqrt(2) = 212.1`V b) Let `I_(0)` be the peak...

2 Answers 1 views
If measured value of resistance `R = 1.05Omega` wire diameter `d = 0.60 mm` and length `l = 75.3 cm` If maximum error in resistance measurment is `0.0

`((Deltarho)/(rho))_(max)=(DeltaR)/(R)+2(Deltad)/(d)+(Deltal)/(l)` `DeltaR = 0.01 Omega` `Deltad = 0.01 mm` (least count) `Deltal = 0.1 cm` (least count) `((Deltarho)/(rho))_(max)=((0.01Omega)/(1.05Omega)+2(0.01mm)/(0.60mm)+(0.1cm)/(75.3cm))xx100=4.3%` .

2 Answers 1 views
In the previous question, find the maximum permissible error in resistivity and resistance.

`((DeltaR)/(R))_(max)=(Deltai)/(i)+(Deltav)/(v)=(0.1)/(10.0)+(0.1)/(100.0)=1.1%rArr((dp)/(rho))_(max)=2.42%` .

2 Answers 1 views
Using screw gauge the observation of the diameter of a wire are `1.324,1.326,1.334,1.336cm` respectively Find the average diameter the mean error the

`vecD=(sum(D))/(N)=(1.324+1.326+1.334+1.336)/(4)=1.330` `DeltaD_(1) = 1.324 -1.330 = - 0.006` `DeltaD_(2) = 1.326 -1 1.330 = - 0.004` `DeltaD_(3) = 1.334 - 1.330 = 0.004` `DeltaD_(4) = 1.336 - 1336 -1 1.330...

2 Answers 1 views
When an AC voltage, of variable frequency is applied to series L-C-R circuit , the current in the circuit is the same at 4 kHz and 9 kHz. The current

Correct Answer - D (d) `I_(1) = I_(2)` `therefore omega_(1)L - 1/(omega_(1)C) = 1/(omega_(2)C) - omega_(2)L` Solving this, we get `1/sqrt (LC)`= responance frequency = `sqrt (omega_(1)omega_(2))` At resonance frequency ,...

2 Answers 3 views
The mass of a cube has error of 2% and the length of its edge has error of 1%. What will be the maximum percentage error in calculation of its density

Density of cube `(p)=(M)/(V)=(M)/L^(3)) therefore((Deltap)/(P))_("max")xx100=((DeltaM)/(M)xx100)+3(DeltaL)/(L)xx100)=2%+3(1%)=5%`

2 Answers 1 views
The heat generated in a cirucit is dependent upon the resstance, current and time for which the current is flown. If the error in measuring the above

H=PRt `(DeltaH)/(H)=(2DeltaI)/(I)+(DeltaR)/(R)+(Deltat)/(t)=2(2%)+1%+1%` =6%

2 Answers 1 views
X