Bissoy
Login
Get Advice on Live Video Call
Earn $ Cash $ with
consultations on Bissoy App
If joint is to fail by crushing of socket collar then estimate the diameter of socket collar. Given Permissible compressive stress= 126.67 N/mm².; Spigot dia=65mm; thickness 0f collar=15mm
A
131mm
B
139mm
C
141mm
D
149mm
Correct Answer:
131mm
Compressive stress= P/ .
If knuckle joint is to fail by crushing failure of pin in fork, then determine the diameter of knuckle pin when 50kN axial tensile force act on rods. Given: Max allowable compressive stress=25N/mm², thickness of each eye of fork=25mm.
A
40mm
B
50mm
C
60mm
D
70mm
Calculate minimum wall thickness given a cylindrical prestressed water tank of internal diameter 30m over a depth of 7.5m and the permissible compressive stress at transfer is 13n/mm2 and the maximum compressive stress under working pressure is 1n/mm2 and the loss ratio is 0.75?
A
43.8
B
82.3
C
64.5
D
90.4
When an open coiled helical compression spring is subjected to an axial compressive load, the maximum shear stress induced in the wire is (where D = Mean diameter of the spring coil, d = Diameter of the spring wire, K = Wahl's stress factor and W = Axial compressive load on the spring)
A
$$\frac{{{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
B
$$\frac{{2{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
C
$$\frac{{4{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
D
$$\frac{{8{\text{WD}}}}{{\pi {{\text{d}}^3}}} \times {\text{K}}$$
A machine vice whose length of the handle is 150mm and the coefficient of friction for thread and collar are 0.15 and 0.17 respectively has a force applied at handle of 125N. Also the outer and inner diameters of collar are 55mm and 45mm respectively. Find the collar torque in terms of clamping force W assuming uniform wear theory if nominal diameter=22mm and pitch=5mm.
A
4.5W
B
5.4W
C
4.25W
D
3.37W
Calculate the diameter of the rivets by crushing consideration if permissible compression stress in rivets is 120N/mm², thickness of plate 3mm and P=15kN.
A
10.4mm
B
11.5mm
C
9.2mm
D
8.6mm
From an alloy, two specimens are machined and tested separately under tension and compression. The engineering stress-strain curves as well as the true stress-true strain curves for tension and compression are plotted in the same diagram. Identify the correct statements:
P. The engineering stress-strain curves in tension and compression are identical.
Q. The true stress-true strain curve in compression is lower than the true stresstrue strain curve in tension due to Bauschinger effect.
R. The true stress-true strain curve in tension is above the corresponding engineering stress-strain, curve.
S. The true stress-true strain curve in tension and compression are identical.
A
P, Q
B
Q, R
C
Q, S
D
R, S
In a rivet joint thickness of the plate is t and the length of the margin is m. If the permissible shearing stress of the plate is τs, find the shear strength of the joint at the margin.
A
mtτs
B
m2tτs
C
2mtτs
D
m2τs
In case of joint products, the main objective of accounting of the cost is to apportion the joint costs incurred up to the split off point. For cost apportionment one company has chosen Physical Quantity Method. Three joint products ‘A’, ‘B’ and ‘C’ are produced in the same process. Up to the point of split off the total production of A, B and C is 60,000 kg, out of which ‘A’ produces 30,000 kg and joint costs are Rs 3,60,000. Joint costs allocated to product A is.
A
Rs 1,20,000
B
Rs 60,000
C
Rs 1,80,000
D
None of the these
The maximum diameter of the hole that can be punched from a plate of maximum shear stress $${\frac{1}{4}^{{\text{th}}}}$$ of its maximum crushing stress of punch, is equal to (where t = Thickness of the plate)
A
1t
B
2t
C
4t
D
8t
Tresca or maximum-shear stress criteria assumes that yielding occurs when the maximum shear stress reaches a value of the shear stress in the uniaxial tension test. Assume the principal stress being σ1, σ2, σ3 where σ1 is largest, and σ3 is the smallest principal stresses. Find the value of minimum shear stress to cause yielding, given that yield stress in tension is equal to σo?
A
τ = σo
B
τ = σo/2
C
τ = σo/3
D
τ = σo/4